LumberJocks

LumberJocks Woodworking Forums

  • Advertise with us
All Topics Replies Last post
View hoss1947's profile

Replacing drive belt on Ryobi AP 10 Planer

02-12-2013 06:27 AM by hoss1947 in Power Tools, Hardware and Accessories

I recently had to do this on my old AP10 planer, did a lot of searching and f...

16 06-18-2018 10:31 AM
View lumberames's profile

hardboard notch protection?

06-16-2018 11:07 AM by lumberames in Wood & Lumber

hi. Need some advice on protecting a notch I made (btw: poorly) on a 1/8 inc...

8 06-18-2018 10:03 AM
View BroncoBrian's profile

Table Saw Fence Alignment

06-16-2018 10:16 PM by BroncoBrian in Power Tools, Hardware and Accessories

Good evening everyone! I know there are old threads about this, but I thou...

20 06-18-2018 10:00 AM
View chrisstef's profile (online now)

Off-topic content. Click to see the post.

08-24-2017 11:38 AM by chrisstef in Coffee Lounge

5995 06-18-2018 09:54 AM
View StumpyNubs's profile

Stumpy Nubs Woodworking Journal- A truly unique online publication (part 4)

08-24-2017 10:23 AM by StumpyNubs in Woodworking Skill Share

Join us! This is a family-friendly, non-political, no bickering or arguing zo...

17544 06-18-2018 09:53 AM
View Clarkswoodworking's profile

Off-topic content. Click to see the post.

06-17-2018 05:30 PM by Clarkswoodworking in Coffee Lounge

6 06-18-2018 09:45 AM
View AAL's profile

Wet grinder recommendation

06-17-2018 10:10 AM by AAL in Woodcarving

I’m just starting into a new hobby of chip carving and have started a c...

7 06-18-2018 09:43 AM
View nukegumbo's profile

Lumber rack

06-17-2018 10:10 PM by nukegumbo in Wood & Lumber

Need ideas on how to convert this metal rack to a lumber rack. I don’t ha...

3 06-18-2018 09:39 AM
View nickbatz's profile

Router recommendations: good, fast, cheap - I want all three

06-16-2018 02:34 PM by nickbatz in Power Tools, Hardware and Accessories

I’m in the market for a router with a 1/2” collet to use the Freu...

24 06-18-2018 09:28 AM
View Littleroom's profile

Jointer help

06-17-2018 10:03 PM by Littleroom in Power Tools, Hardware and Accessories

Hey folks, So I bought a used Mastercraft(yeah I know…) Jointer mode...

7 06-18-2018 08:30 AM
View Rick's profile

Off-topic content. Click to see the post.

06-15-2018 09:40 PM by Rick in Coffee Lounge

17 06-18-2018 08:23 AM
View BigRedKnothead's profile

A Furniture Makers Forum

10-10-2013 03:42 PM by BigRedKnothead in Woodworking Skill Share

While I love me some Hand planes, Workbenches, Tool boxes and the like…...

9352 06-18-2018 08:10 AM
View Randy T's profile

storing finished product

06-08-2018 07:30 PM by Randy T in Finishing

Folks:I have been asked to make some plaques which will be finished with lacq...

10 06-17-2018 11:38 PM
View JADobson's profile

Removing paste wax from oak pores

06-17-2018 01:57 PM by JADobson in Finishing

I just finished a box and I guess I still had a few open pores in the oak. My...

10 06-17-2018 10:03 PM
View RobHannon's profile

Letting the smoke out

06-14-2018 04:16 PM by RobHannon in Power Tools, Hardware and Accessories

My old Black and Decker 3×21 belt sander made a horrible noise today whi...

2 06-17-2018 09:55 PM
View hairy's profile

Incra TS fence push block

06-17-2018 12:35 PM by hairy in Jigs & Fixtures

Since I installed the Ark Shark guard I want to use it as much as possible. T...

1 06-17-2018 09:30 PM
View GR8HUNTER's profile (online now)

for BAS350 owners only OR unless you have adjusted lower bearings

06-17-2018 02:10 PM by GR8HUNTER in Power Tools, Hardware and Accessories

I had to recently change my blade so I went with a 1/2 inch since I am mostly...

3 06-17-2018 09:27 PM
View Grumpy's profile

Off-topic content. Click to see the post.

05-27-2009 07:14 PM by Grumpy in Coffee Lounge

3676 06-17-2018 09:04 PM
View JohnMcClure's profile

WOOD ID - is this nasty looking wood diseased elm?

06-17-2018 10:09 AM by JohnMcClure in Wood & Lumber

Small trunk, 8”-6” diameter. Bark makes me think elm… very ...

5 06-17-2018 09:01 PM
View paulmon's profile

Where does all the crap come from?!

06-14-2018 10:39 PM by paulmon in Wood & Lumber

When you have a small work space, you have to get creative. That means keepin...

13 06-17-2018 08:46 PM

« prev 1 2 3 4 5 ... 4527 next »
90536 topics

RSS FEED

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com