LumberJocks

finally success at turning mahogany!

  • Advertise with us
Project by Blake Haskins posted 09-10-2017 04:56 AM 1088 views 0 times favorited 5 comments Add to Favorites Watch

I turned a small bowl from mahogany, its a pretty raw turning video, but I narrated it in an informative manner, so you may learn how to turn for yourself.
In the past I haven’t had much luck turning mahogany, it usually explodes halfway through the project,

If you enjoyed this vihttps://www.youtube.com/watch?v=Ax5jRg5L8vU&feature=youtu.be

if you have any idea for future videos/projects let me know.

-- make sure you subscribe to my channel- https://www.youtube.com/channel/UCRuWi7P7eIcNOckoxBI-ZRA





5 comments so far

View ralbuck's profile

ralbuck

3422 posts in 2024 days


#1 posted 09-10-2017 05:01 AM

Nice looking bowl.

-- SAWDUST is THERAPY without a couch! just rjR

View helluvawreck's profile

helluvawreck

27833 posts in 2624 days


#2 posted 09-10-2017 01:40 PM

Blake, this is a beautiful piece and you did a fine job on it.

helluvawreck aka Charles
http://woodworkingexpo.wordpress.com

-- If a man does not keep pace with his companions, perhaps it is because he hears a different drummer. Let him step to the music which he hears, however measured or far away. Henry David Thoreau

View Blake Haskins 's profile

Blake Haskins

206 posts in 995 days


#3 posted 09-10-2017 06:23 PM


Nice looking bowl.

- ralbuck


Blake, this is a beautiful piece and you did a fine job on it.

helluvawreck aka Charles
http://woodworkingexpo.wordpress.com

- helluvawreck


Thanks alot!!

-- make sure you subscribe to my channel- https://www.youtube.com/channel/UCRuWi7P7eIcNOckoxBI-ZRA

View UncleStumpy's profile

UncleStumpy

731 posts in 2070 days


#4 posted 09-10-2017 09:26 PM

Great bowl!
I was actually thinking about turning a piece of African Mahogany and now I am worried about it exploding!
Are there always problems or just the batch you had?

-- "They don't want it perfect - they want it SPECIAL"

View LesB's profile

LesB

1284 posts in 3200 days


#5 posted 09-12-2017 12:05 AM

Nice bowl. You are doing quite well for you age.

I have a couple of suggestions that I think you might find useful.
First, I see in the video you have a chuck for the lathe. So, if you also have a router you can use it to create a recess in the bottom of your blank to mount it instead of using the screw mount. It is done by making a circle template with a 24” long b6 6” piece of 1/2” plywood. Then make a hole in the center the diameter you want the recess in the blank to be, plus about 1/4”. Place the template over the center of the blank and securly clamp it in place. I usually do it across the corner of my work bench so I can clamp the whole thing to the bench.
Then with a template guide mounted on your router base and a 8 degree dovetail bit installed and adjusted for the depth of the template plus 3/16 to 1/4” for th depth of the recess, rout the recess in the bottom of the blank. You can now mount it directly to the chuck jaws and it will be a lot more stable than the screw mount. I usually do this on the side of the blank that I intend tol be the inside of the bowl. Then I completely finish turning the bottom (including sanding). creating a new chuck recess in the bottom in the process. Now you just have to flip the blank around and finish turning the inside. I make several circle templates for various size bowls an chuck jaws.

Next. If you want to eliminate the “chipping” of the edges of a Square turning you should glue 1/4” scrap pieces of a soft wood the width of the blank to all four of the edges of the blank. Now the edges of your blank are protected from chipping out and when you are done you can saw or plane and sand of the scrap pieces.

In this piece you commented on the rough finish and had to use 80 grit sand paper. Did you try using a very sharp scraper with the bowl turning at fairly high speed (1500 rpm or more). That usually removes the tearing and
roughness.
If you have trouble with my explanations feel free to contact directly.

-- Les B, Oregon

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com