Meterk, NeJe, etc. 1500mW Laser Engraver

  • Advertise with us
Review by Andybb posted 10-17-2018 07:00 PM 726 views 2 times favorited 5 comments Add to Favorites Watch
Meterk, NeJe, etc. 1500mW Laser Engraver No-picture-s No-picture-s Click the pictures to enlarge them

I grabbed this machine off of Amazon using a $100 gift card that I had.

I also did a little research on these. They are inexpensive because they are made using the stripped down laser and transport systems built into a gazillion blu-ray and cd burners with virtually no modification other than the circuit board. They are basically all the same, so Neje, Meterek, Qiilo, Sixdu, Decaker…etc. same guts. This one came with software that says Neje on it, so it’s generic. Here is a vid of someone dismantling one.

I short..It works great once you figure out how to turn it on and how to use the software. As expected, the instructions absolutely suck but that is just a minor inconvenience. Loaded the drivers and the software found the machine without any issues. It seems that 3 things control the quality of your results. Burn time, # of repetitive passes and material you are burning. After a test on cardboard I went right to hard maple. Increase the burn time and the laser slows down and really digs into the material but if you are doing something that requires a lot of detail like a very small butterfly it seems you are better off lowering the burntime and making 2 or 3 passes. Make no mistake about it, you are “burning” the material so you can understand that a longer burn time kinda decreases the “resolution” as it burns the surrounding material. As far as resolution goes, it can print words in sizes too small to even see with incredible detail. It works on pens just fine. (dowels in my test) The software comes with 300-400 images and I was able to grab a jpeg of Muhammad Ail’s eyes off of the web and print that. I’m sure there are other software suites that can do more but for me it gives me what looks like the suite of MS Word fonts so I’m good. I got the 1500mw version since I read somewhere that somebody didn’t see a difference between that and the 2000mw version. I’m thinking that the 1000mw version would work just fine also. Never got the burn time anywhere near maxed out. Took about 10 mins to make that butterfly logo.

Max image that it can burn is 1 1/2” (38mm) seems to be about the limit. Not sure why I had 3” in my head. Using the provided software (which is basic and easy to use) nothing will print larger than the box provided. When the butterfly filled the box the resulting image is still only 1.5” wide. Kinda wondering what the next size up is but I imagine it would be spendy as this seems to be the limit of the blu-ray burner hardware.

The Decaker model that Rich is looking at uses the same laser and transport system and carriages as the others except that both transports are mounted in the top as opposed to the x-axis on top and the y-axis on the bottom. I might just exchange mine for one like Rich is getting as I can see the value in being able to sit the whole machine on top of a workpiece and it’s only $95 on gear best.

Now to figure out how to get some type of accent color into dark colored pens like in the OP.

Rich, I think you will be happy with your purchase.

It took about 3 mins to print on those dowels and about 20mins for the large butterfly and text under it. It also gives me the ability to orient the printing based on the customer being right or left handed. Most folks don’t realize that off the shelf pens and mugs etc are for righties as the print is upside down if you’re a lefty.

I grabbed it because I have 2 customers who want either name or initials in their pen. I quoted them $20 additional for each pen so I should recoup the expense after not too long.

-- Andy - Seattle USA

View Andybb's profile


1377 posts in 777 days

5 comments so far

View Andre's profile (online now)


2132 posts in 1979 days

#1 posted 10-18-2018 05:25 AM

Good review, could see some uses in the future.

-- Lifting one end of the plank.

View JADobson's profile


1240 posts in 2284 days

#2 posted 10-22-2018 04:24 PM

Thanks for this review Andy.

-- No craft is very far from the line beyond which is magic. -- Lord Dunsany — Instagram @grailwoodworks

View cmmyakman's profile


204 posts in 2829 days

#3 posted 10-23-2018 06:57 PM

This was a very useful review.

-- You can't fail if you don't give up.

View Ocelot's profile


2105 posts in 2811 days

#4 posted 10-23-2018 07:08 PM

===>Christmas list.

View WoodenDreams's profile


209 posts in 84 days

#5 posted 10-25-2018 05:40 AM

Was looking on ebay a week or two ago for a smaller laser engraver, and didn’t pull the trigger to get one. Just wasn’t sure of the surface settings & quality the smaller ones would produce. I appreciate the review you posted. Good info.

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics