LumberJocks

How do you cross cut on your table saw???

  • Advertise with us

« back to Power Tools, Hardware and Accessories forum

Forum topic by scribble posted 05-31-2018 09:01 PM 1218 views 0 times favorited 23 replies Add to Favorites Watch
View scribble's profile

scribble

196 posts in 2342 days


05-31-2018 09:01 PM

Topic tags/keywords: question tablesaw milling

I am looking to see how people do cross cutting on there table saws. Are you using a sled of some sorts or just using a miter gauge.

-- If you can't read it Scribble wrote it!! “Experience is merely the name men gave to their mistakes.”


23 replies so far

View bondogaposis's profile

bondogaposis

4973 posts in 2492 days


#1 posted 05-31-2018 09:04 PM

For short pieces I use the miter gauge with an sacrificial fence, longer pieces I use a sled and for really long pieces I cut to rough length with a circular saw or miter saw.

-- Bondo Gaposis

View MrUnix's profile

MrUnix

6920 posts in 2340 days


#2 posted 05-31-2018 09:12 PM

Are you using a sled of some sorts or just using a miter gauge.
- scribble

Yes.

Cheers,
Brad

-- Brad in FL - In Dog I trust... everything else is questionable

View knotscott's profile

knotscott

8129 posts in 3516 days


#3 posted 05-31-2018 10:00 PM

Osborne EB-3 miter gauge with fence that has stop block and a sandpaper face.

-- Happiness is like wetting your pants...everyone can see it, but only you can feel the warmth....

View jdmaher's profile (online now)

jdmaher

435 posts in 2720 days


#4 posted 05-31-2018 10:02 PM

Rough cuts with a miter gauge. Final / finish cuts with a sled (Dubby).

In fact. most of the cuts are done with the sled. I’ll sometimes do rough cuts with a hand or circular saw (biggish lumber), and I have enough off-cuts of my favorite woods that I can usually select a piece that’s close enough to finish size. And the particular sled I’m using makes it real easy to dial in a length and reliably repeat it.

-- Jim Maher, Illinois

View Walker's profile

Walker

146 posts in 613 days


#5 posted 05-31-2018 10:31 PM

How do I cross cut on my table saw? I lift the wood right over it and make the cut on my miter saw.

Joking aside, I only have a cheap contractor saw (no space or money for a real table saw). I have a sled I use, made with Micro Jig’s “Zero Play” miter bars which is okay, but the saw is so inaccurate I needed to find a better way. I bought a nice sliding compound miter saw. The cut capacity is big enough for most jobs. Now I leave the table saw set up for rip cuts most of the time.

-- ~Walker

View Andre's profile

Andre

2056 posts in 1947 days


#6 posted 05-31-2018 10:33 PM

Short pieces Kreg miter gauge, real small and repeatable cuts sled, hacking planks down to size Hand saw!

-- Lifting one end of the plank.

View builtinbkyn's profile

builtinbkyn

2636 posts in 1081 days


#7 posted 05-31-2018 10:34 PM

Same as Bondo.

-- Bill, Yo!......in Brooklyn & Steel City :)

View Rick  Dennington's profile

Rick Dennington

6152 posts in 3335 days


#8 posted 05-31-2018 11:21 PM

I have 4 different size sleds for different size woods…..I hardly ever cross cut with a miter gauge….Depending on what I have to have, I also cross cut with my radial arm saw….Then move it to one of the sleds….!!

-- " It's a rat race out there, and the rats are winning....!!"

View TheFridge's profile

TheFridge

10243 posts in 1627 days


#9 posted 05-31-2018 11:28 PM

Both

-- Shooting down the walls of heartache. Bang bang. I am. The warrior.

View Charlie H.'s profile

Charlie H.

276 posts in 791 days


#10 posted 06-01-2018 12:22 AM

I have the stock miter gauge locked at 90 degrees with a long laminated plywood sacrificial face and it’s equipped with a flip stop.
I mostly use that in the right miter slot when I cut 45 degree bevels.

I have an Incra HD1000 that I use in the left miter slot, it’s good for batching out parts.

I use the crosscut sled a lot.
It is especially useful for small parts.

-- Regards, Charlie in Rowlett, TX --------I talk to myself, because sometimes I need expert advice.---------

View BroncoBrian's profile

BroncoBrian

776 posts in 2099 days


#11 posted 06-01-2018 12:30 AM

Yep, same as above. Icra Miter, and crosscut sled.

I think the Incra V27 is a great value and you can add a face to it.

-- I'd like to see a forklift lift a crate of forks. It'd be so damn literal!

View woodbutcherbynight's profile

woodbutcherbynight

5558 posts in 2550 days


#12 posted 06-01-2018 01:39 AM

These two are the most commonly used ones. I have a larger sled but no pics. Nothing fancy, no special miter bars just wood screws and some glue. Little time tuning them up and they have remained accurate.

-- Live to tell the stories, they sound better that way.

View MrWolfe's profile

MrWolfe

93 posts in 264 days


#13 posted 06-01-2018 01:45 AM

I have an Osbourne EB-3. I use it for most cuts. There is even a video on how to use it for crosscutting panels.
I will probably make a dedicated small parts sled but I use the EB-3 for everything else. I sometimes rough cut full sheets with a circular saw and cut them to finish on the table saw too.

https://www.youtube.com/watch?v=_RcChmHntes&t=10s

View clin's profile

clin

927 posts in 1137 days


#14 posted 06-01-2018 03:22 PM

I use a sled for all cross cuts. I only use my Osborne miter gauge if making an angled cut.

-- Clin

View Derek Cohen's profile

Derek Cohen

393 posts in 4109 days


#15 posted 06-01-2018 03:49 PM

Hammer K3 Slider …

Regards from Perth

Derek

-- Buildiing furniture, and reviewing and building tools at http://www.inthewoodshop.com

showing 1 through 15 of 23 replies

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com