LumberJocks

What is this tool used for?

  • Advertise with us

« back to Hand Tools forum

Forum topic by HokieKen posted 06-11-2018 01:25 PM 882 views 0 times favorited 16 replies Add to Favorites Watch
View HokieKen's profile (online now)

HokieKen

7194 posts in 1344 days


06-11-2018 01:25 PM

I recently inherited this tool. It was made by AMT and appears to me to be a spoon carving tool of some sort. But, I couldn’t figure out how it could possibly be used.

The edges are blunt and the recess in the center seems to be where business is conducted. The cutout is shown in the photos below. There is a bevel on the outside (convex side) of the cutout and the inside (concave side) is smooth with the cylindrical face. The outer edges and end are all completely blunt. So seemingly it would be used to shave the outside of round pieces? I couldn’t find any similar examples online so I thought I’d turn to the collective LJ brain trust ;-)

Thanks for any help! Additional photos below.

-- Kenny, SW VA, Go Hokies!!!


16 replies so far

View swirt's profile

swirt

3451 posts in 3178 days


#1 posted 06-11-2018 01:31 PM

I think it is a chamfer. Run it in either direction along the corner edge of a board and it will chamfer the edge.

-- Galootish log blog, http://www.timberframe-tools.com

View TheFridge's profile

TheFridge

10767 posts in 1692 days


#2 posted 06-11-2018 01:31 PM

Looks like a tool for rounding edges.

-- Shooting down the walls of heartache. Bang bang. I am. The warrior.

View waho6o9's profile

waho6o9

8525 posts in 2783 days


#3 posted 06-11-2018 01:35 PM

Going with the chamfer as well.

View doubleG469's profile (online now)

doubleG469

659 posts in 650 days


#4 posted 06-11-2018 01:37 PM

Chamfer

-- Gary, Texas

View Mosquito's profile

Mosquito

9543 posts in 2498 days


#5 posted 06-11-2018 01:37 PM

I agree with Fridge, for rounding corners. The Stanley #28 and #29 cornering tools have the same type of cutting mechanism

-- Mos - Twin Cities, MN - http://www.youtube.com/MosquitoMods - http://www.TheModsquito.com

View bondogaposis's profile

bondogaposis

5098 posts in 2557 days


#6 posted 06-11-2018 01:40 PM

Chamfer tool.

-- Bondo Gaposis

View Brit's profile

Brit

7547 posts in 3049 days


#7 posted 06-11-2018 01:43 PM

I’m with Fridge on this one. He’s bang on the money.

-- https://www.clickasnap.com/Andy61 - Andy - Old Chinese proverb says: "If you think something can't be done, don't interrupt man who is doing it."

View BurlyBob's profile

BurlyBob

5987 posts in 2471 days


#8 posted 06-11-2018 01:50 PM

I’m with Fridge as well.

View TheFridge's profile

TheFridge

10767 posts in 1692 days


#9 posted 06-11-2018 01:58 PM

Hey Brit. I don’t bang for money. Just for pleasure.

So how many are still with me :)

-- Shooting down the walls of heartache. Bang bang. I am. The warrior.

View DBDesigns's profile

DBDesigns

183 posts in 203 days


#10 posted 06-11-2018 02:00 PM

FYI, this is a pretty cool antique since it is not one of the more common Stanley models. It loos like it would be much more comfortable in your hand than the Stanley churchkey roundover tool.
Keep it sharp and enjoy an interesting part of your ancestor’s legacy.

-- I remember when Grateful wasn't Dead

View HokieKen's profile (online now)

HokieKen

7194 posts in 1344 days


#11 posted 06-11-2018 02:01 PM

Ding ding ding. We have a winner! It’s obviously a round-over tool now that Fridge et al point it out. Funny how once I initially thought “carving” my brain couldn’t leave that track :-)

For all who said chamfer tool, close but that would have a flat face and most likely an angle guide of some sort.

Thanks for the pic of the Stanley tools Mos’. That eliminates any doubt ;-)

-- Kenny, SW VA, Go Hokies!!!

View HokieKen's profile (online now)

HokieKen

7194 posts in 1344 days


#12 posted 06-11-2018 02:02 PM

Now I’m gonna go carve a spoon with round corners…

-- Kenny, SW VA, Go Hokies!!!

View DBDesigns's profile

DBDesigns

183 posts in 203 days


#13 posted 06-11-2018 02:31 PM

FYI, this is a pretty cool antique since it is not one of the more common Stanley models. It looks like it would be much more comfortable in your hand than the Stanley church key round-over tool.
Keep it sharp and enjoy an interesting part of your ancestor’s legacy.

-- I remember when Grateful wasn't Dead

View Don W's profile

Don W

19018 posts in 2773 days


#14 posted 06-12-2018 10:34 PM

I think fridge is correct on the tool, but disagree about banging for money. You’ve got to love your job or it’s just hard work!!

-- http://timetestedtools.net - Collecting is an investment in the past, and the future.

View Rick S...'s profile

Rick S...

10913 posts in 3239 days


#15 posted 06-12-2018 10:43 PM



I agree with Fridge, for rounding corners. The Stanley #28 and #29 cornering tools have the same type of cutting mechanism

- Mosquito

YEP! Them’s the ones! I have the same ones.

Rick

-- I Chose "The Road Less Travelled" Now I'm Totally Lost! (Ontario, CANADA)

showing 1 through 15 of 16 replies

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com